The Patterning Process: Part II

by
posted on December 16, 2015
** When you buy products through the links on our site, we may earn a commission that supports NRA's mission to protect, preserve and defend the Second Amendment. **
patterning_process_part_2.jpg

Now, getting back to the matter of patterning a buck named Big Jr. As you may remember, I jumped the cameras several hundred yards from where I was getting nighttime-only photos of the deer. I moved them in the direction he was coming from when he approached the original camera. That first photo of a buck during an evening sequence tells you a lot about where he might be living.

I had to come in to the new area from the opposite side of a large creek in order to approach it quickly and easily with an ATV. I put out four cameras. The first was on the edge of a soybean field on a small ridge top overlooking the creek. The second hung parallel to the creek but down in a valley, on the edge of a small food plot. The third camera was about 200 yards farther from the site of the first photos—a short ways into a seven-acre bean bottom. That one was likely 400 yards from the original camera. I placed number four in a small clover plot another 200 yards farther west.

I had cast a wide net and felt he had to show up on one of those cameras. I could drive easily to all four of the new sites making it easy for me to check the cameras and refresh the corn in front of them quickly.

Immediately, I began getting dozens of photos of the buck on the camera in the seven-acre bottom each evening. He never showed on the two that were closer to the original camera site, but he was popping in occasionally on the camera in the small plot farther west. You have to be a little bit careful when using bait in front of your cameras because the deer may be coming for the bait but not normally using that area. When you stop baiting, they stop coming.

Obviously, though, with the number of photos I was getting of the buck in the big field, I was closing in on his core area. I had no doubt he was living in the cover surrounding it.

It is tough to bowhunt a big field, but I had an idea where I would hunt those timber areas around it. The plan was starting to come together. All I needed was to see some daylight photos of the buck and I would start to hunt him.

As is common, the first daylight photos came with a cold front. This one was in mid-October. Unfortunately for me, that front also coincided with Iowa’s early muzzleloader season. My neighbor to the south shot Big Jr. that very first weekend with a muzzleloader.

Just as soon as I decided it was time to make my move, it was already too late!

Had I been hunting the buck with a gun I would have likely killed him Saturday evening (the first day of the cold front and opening day of the early muzzleloader season). I had daylight photos of him walking across the big field on another camera I had placed on my ground blind and set to take a photo every minute of the afternoon. The neighbor killed him the next evening. I had a one-day window; not nearly enough time with a bow.

Though I didn’t kill the buck, the process did work. And I have used this method several times to pinpoint the best starting point when hunting a specific buck. You don’t always get them – the bow is a very limited range arm after all—but at least using this method, you are in the game most of the time.

Now the rut is over and I have the cameras back out trying to find another buck to chase. Once I do, the process starts over again.

Latest

008 MWIBHRB HD Ext 01
008 MWIBHRB HD Ext 01

Range Review: Midwest Industries Bounty Hunter Revolver Brace

Thanks to Midwest Industries new Revolver Brace, you can easily mount a stabilizing brace to your favorite hunting revolvers. Check out B. Gil Horman's review of this game-changing product.

First Look: Marlin Mad Pig Customs Model 1894

Marlin has introduced its Mad Pig Customs Model 1894, a rifle developed—as its name implies—in collaboration with Mad Pig Customs. Built on Marlin's iconic lever‑action rifle platform, this model delivers modern, factory‑installed features previously found only on custom builds.

Funding Authorized to Conserve Critical Wetland Habitat

The Department of the Interior has announced that $44.79 million in North American Wetlands Conservation Act (NAWCA) funds have been approved by the Migratory Bird Conservation Commission. They will provide the U.S. Fish and Wildlife Service—and its partners—the ability to conserve, restore or enhance 185,203 acres of critical wetland and associated upland habitat for migratory birds across the United States.

Behind the Bullet: The .30-378 Weatherby Magnum

Curious about one of the original wonder cartridges? A cartridge that literally broke the 6000 fps mark with specialized, lightweight options? Follow along with Phil Massaro as he dives into the .30-378 Weatherby Magnum.

New for 2026: Muddy Cloak OZ3 and OZ5 Ozone Generators

Muddy Outdoors has launched the Cloak OZ3 and OZ5 Ozone Generators—two high-output scent control solutions designed to give hunters a true edge in the field.

Varmint Hunting 101: Tips and Overview

Looking for a way to spend your offseason that scratches your hunting itch? Try varmint hunting. Follow along with Tim Hovey as he discusses how to get into the pursuit, and some basic tips to get you rolling.

Interests



Get the best of American Hunter delivered to your inbox.